Microphone mods - Progressive Rock Music Forum

Author

Message

Topic Search

Topic Options

Davesax1965 View Drop Down

Forum Senior Member

Joined: May 23 2013
Location: UK
Status: Offline
Points: 2826

Topic: Microphone mods
Posted: July 01 2017 at 08:22

Hi folks, I'm vaguely thinking of modding an MXL 990 to take a larger capsule (RK-47) and possibly doing some circuit board changes.

Anyone done anything like this and do the results justify the outlay and work ?

Cheers

Dave

pitfall

Forum Senior Member

Joined: June 22 2012
Location: Essex, England
Status: Offline
Points: 109

Posted: July 02 2017 at 16:05

Most certainly - I'd say that 80% of the sound of a microphone comes from the capsule, 10% from the electronics (as long as they are reasonably designed), and 10% from the housing.

The MXL 990 is not a bad mike - but the diaphragm is actually not a large one - it's about a half inch, and is, typically for a far eastern one, a bit on the bright side.

You should end up with a mike which performs as well one costing several times as much.

Alternatively, you could opt for something like an Oktava 219 or 319 secondhand - these sound phenomenal on a lot of sources, and have even been compared to a Neumann U47.

Davesax1965 View Drop Down

Forum Senior Member

Joined: May 23 2013
Location: UK
Status: Offline
Points: 2826

Posted: July 05 2017 at 04:08

Fantastic, thanks, Pitfall. I'll replace the capsule with an RK-47. It's just finding the anvil the capsule sits on. Yep, I thought the PCB was not worth bothering with- most mods I've seen just change a few capacitor values and replace some of the caps with plastic film ones. Won't have much effect.

I'll swap over the capsule and get a modified headbasket with a more open weave. Thanks !!!

Davesax1965 View Drop Down

Forum Senior Member

Joined: May 23 2013
Location: UK
Status: Offline
Points: 2826

Posted: July 06 2017 at 05:58

And I've found some valve mic kits in the interim. Soldering iron out. ;-)

Davesax1965 View Drop Down

Forum Senior Member

Joined: May 23 2013
Location: UK
Status: Offline
Points: 2826

Posted: July 07 2017 at 03:43

Coming along. New headbasket.

RK-47 capsule replacement next, followed by a capacitor upgrade. And I'm looking into 12AX7 based valve microphone kits.

Davesax1965 View Drop Down

Forum Senior Member

Joined: May 23 2013
Location: UK
Status: Offline
Points: 2826

Posted: August 29 2017 at 05:54

End result ? Pretty good. Sensitivity went through the roof. Not given it a proper tryout yet, but it's transformed the microphone.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Davesax1965 Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: May 23 2013 Location: UK Status: Offline Points: 2826	Topic: Microphone mods Posted: July 01 2017 at 08:22
	Hi folks, I'm vaguely thinking of modding an MXL 990 to take a larger capsule (RK-47) and possibly doing some circuit board changes. Anyone done anything like this and do the results justify the outlay and work ? Cheers Dave


pitfall Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: June 22 2012 Location: Essex, England Status: Offline Points: 109	Posted: July 02 2017 at 16:05
	Most certainly - I'd say that 80% of the sound of a microphone comes from the capsule, 10% from the electronics (as long as they are reasonably designed), and 10% from the housing. The MXL 990 is not a bad mike - but the diaphragm is actually not a large one - it's about a half inch, and is, typically for a far eastern one, a bit on the bright side. You should end up with a mike which performs as well one costing several times as much. Alternatively, you could opt for something like an Oktava 219 or 319 secondhand - these sound phenomenal on a lot of sources, and have even been compared to a Neumann U47.

Davesax1965 Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: May 23 2013 Location: UK Status: Offline Points: 2826	Posted: July 05 2017 at 04:08
	Fantastic, thanks, Pitfall. I'll replace the capsule with an RK-47. It's just finding the anvil the capsule sits on. Yep, I thought the PCB was not worth bothering with- most mods I've seen just change a few capacitor values and replace some of the caps with plastic film ones. Won't have much effect. I'll swap over the capsule and get a modified headbasket with a more open weave. Thanks !!!


Davesax1965 Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: May 23 2013 Location: UK Status: Offline Points: 2826	Posted: July 06 2017 at 05:58
	And I've found some valve mic kits in the interim. Soldering iron out. ;-)


Davesax1965 Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: May 23 2013 Location: UK Status: Offline Points: 2826	Posted: July 07 2017 at 03:43
	Coming along. New headbasket. RK-47 capsule replacement next, followed by a capacitor upgrade. And I'm looking into 12AX7 based valve microphone kits.


Davesax1965 Members Profile Send Private Message Find Members Posts Add to Buddy List Reviewer page Forum Senior Member Joined: May 23 2013 Location: UK Status: Offline Points: 2826	Posted: August 29 2017 at 05:54
	End result ? Pretty good. Sensitivity went through the roof. Not given it a proper tryout yet, but it's transformed the microphone.